Flamingo Car Care Philippines - Authorized Distributor

Flamingo Car Care Philippines - Authorized Distributor Authorized Distributor in the Philippines

ā—Flamingo Car Care Philippines - Authorized DistributoršŸ¦© ā—Flamingo Rubberized Undercoat (F021) is a heavy-duty aerosol s...
05/06/2026

ā—Flamingo Car Care Philippines - Authorized DistributoršŸ¦© ā—

Flamingo Rubberized Undercoat (F021) is a heavy-duty aerosol spray designed to protect a vehicleā€™s underbody from rust, corrosion, road salt, and stone chips, while simultaneously acting as a sound deadener to reduce road noise.

Step-by-Step Instructions
Clean the Surface Thoroughly (Crucial Step): The underbody must be completely clean and dry before application. Wash away all mud, grease, oil, and road grime. Use a wire brush or sandpaper to scrape away any loose, flaking rust or old, peeling undercoating.

Mask Off Sensitive Areas: Mask off components that must never be undercoated, including the exhaust system (muffler and tailpipes), catalytic converter, brake discs/drums, oil pan, transmission housing, and drive shafts. The undercoat will smoke or cause damage if applied to hot, moving components.

Shake Vigorously: Shake the aerosol can forcefully for at least 2 minutes to thoroughly mix the heavy, rubberized compound inside.

Spray the Underbody: Hold the can 8 to 12 inches away from the surface. Spray using steady, even, sweeping motions. It is best to apply two thin, even coats rather than one heavy, dripping layer.

Dwell Time Between Coats: Allow the first coat to flash and dry for 15 to 20 minutes before applying the second layer.

Allow to Cure: The coating will be dry to the touch in about 30 minutes, but you should allow the vehicle to cure in a dry environment for 24 hours before driving it on wet roads or rough terrain.



ā—Flamingo Car Care Philippines - Authorized DistributoršŸ¦© ā—Using Flamingo De-Rust Lubricant (F019) is a quick and effecti...
04/06/2026

ā—Flamingo Car Care Philippines - Authorized DistributoršŸ¦© ā—

Using Flamingo De-Rust Lubricant (F019) is a quick and effective way to break free rusted bolts, eliminate annoying squeaks, lubricate moving parts, and protect metal surfaces from moisture and corrosion.

Step-by-Step Instructions
Prep the Surface: Shake the aerosol can vigorously before use. For best results on heavily rusted items, use a wire brush to quickly scrape away any loose, flaky rust crust before spraying.

Target the Area: For tight spaces, deep crevices, or specific targets (like frozen nuts, hinges, or lock cylinders), insert the included slim extension straw into the spray nozzle. For wide surfaces, spray directly from the nozzle.

Apply the Spray: Hold the can 4 to 6 inches away and saturate the rusted or stuck component thoroughly with the lubricant.

Let it Dwell (For Stuck/Rusted Parts):

For everyday lubrication, it works instantly.

For heavily rusted or seized parts, let the fluid soak for 2 to 5 minutes. This gives the deep-penetrating formula time to wick into the microscopic thread gaps and dissolve the rust bond.

Break it Loose / Wipe Down: Tap the metal part lightly with a wrench to help the lubricant pe*****te deeper, then loosen the bolt. If you are using it on tools or panels for rust prevention, wipe away any excessive pooling with a clean microfiber cloth, leaving a thin, protective anti-corrosion barrier behind.



ā—Flamingo Car Care Philippines - Authorized DistributoršŸ¦© ā—Prep the Surface: Shake the aerosol can vigorously before use....
04/06/2026

ā—Flamingo Car Care Philippines - Authorized DistributoršŸ¦© ā—

Prep the Surface: Shake the aerosol can vigorously before use. For best results on heavily rusted items, use a wire brush to quickly scrape away any loose, flaky rust crust before spraying.

Target the Area: For tight spaces, deep crevices, or specific targets (like frozen nuts, hinges, or lock cylinders), insert the included slim extension straw into the spray nozzle. For wide surfaces, spray directly from the nozzle.

Apply the Spray: Hold the can 4 to 6 inches away and saturate the rusted or stuck component thoroughly with the lubricant.

Let it Dwell (For Stuck/Rusted Parts):

For everyday lubrication, it works instantly.

For heavily rusted or seized parts, let the fluid soak for 2 to 5 minutes. This gives the deep-penetrating formula time to wick into the microscopic thread gaps and dissolve the rust bond.

Break it Loose / Wipe Down: Tap the metal part lightly with a wrench to help the lubricant pe*****te deeper, then loosen the bolt. If you are using it on tools or panels for rust prevention, wipe away any excessive pooling with a clean microfiber cloth, leaving a thin, protective anti-corrosion barrier behind.



ā—Flamingo Car Care Philippines - Authorized DistributoršŸ¦© ā—Using Flamingo Electronic Contact Cleaner (F015) is a fast, st...
03/06/2026

ā—Flamingo Car Care Philippines - Authorized DistributoršŸ¦© ā—

Using Flamingo Electronic Contact Cleaner (F015) is a fast, straightforward way to remove oil, grease, dirt, flux residue, and moisture from sensitive electrical components. It evaporates instantly and leaves zero residue behind.

Step-by-Step Instructions
Power Down & Unplug (Critical Safety Step): Turn off the device, disconnect it from its power source, and remove all batteries. Never spray contact cleaner into live, energized electrical circuits to avoid short circuits, damage, or accidental sparks.
Let Components Cool: If the electronics were running and feel warm, allow them to cool down to room temperature before spraying.

Prep and Target: Shake the aerosol can vigorously. Insert the included slim extension straw into the spray nozzle for precise targeting inside tight spaces (like circuit boards, switches, charging ports, or sensors).

Spray Thoroughly: Hold the can 4 to 6 inches away from the surface. Spray the contacts generously, allowing the high-pressure liquid to wash away the built-up dust, grease, and grime.

Tilt to Flush: Tilt the component slightly while spraying so the fluid and loosened dirt can easily drain off the surface instead of pooling inside the casing.

Air Dry Completely: Flamingo Contact Cleaner dries in seconds. However, as an extra safety precaution, wait at least 3 to 5 minutes to ensure all hidden moisture has fully evaporated before reinstalling batteries or plugging the power back in.



ā—Flamingo Car Care Philippines - Authorized DistributoršŸ¦© ā—Power Down and Unplug (Critical Safety Step): Always turn off ...
03/06/2026

ā—Flamingo Car Care Philippines - Authorized DistributoršŸ¦© ā—

Power Down and Unplug (Critical Safety Step): Always turn off the device, disconnect it from its power source, and remove any batteries. Never spray this cleaner onto live, energized electrical circuits to prevent accidental short circuits or sparks.

Let Components Cool: If the electronics were running and are hot, allow them to cool down to room temperature before spraying.

Shake and Target: Shake the aerosol can well. For precise targeting inside tight spaces (like circuit boards, switches, sensors, or charging ports), insert the included slim extension straw into the spray nozzle.

Spray the Contacts: Hold the can about 4 to 6 inches away from the target surface. Spray the area thoroughly, letting the liquid flush away the built-in dirt, dust, and oil grease.

Tilt and Drain: Tilt the component slightly while spraying so the fluid and loosened grime can easily run off the surface rather than pooling inside the electronics.

Allow to Dry Completely: Flamingo Contact Cleaner evaporates in seconds. However, as an extra safety measure, wait at least 3 to 5 minutes to ensure every trace of moisture has completely vanished before reinstalling batteries or plugging the power back in.



ā—Flamingo Car Care Philippines - Authorized DistributoršŸ¦© ā—Using Flamingo Wheel & Rim Cleaner (F014) is a straightforward...
02/06/2026

ā—Flamingo Car Care Philippines - Authorized DistributoršŸ¦© ā—
Using Flamingo Wheel & Rim Cleaner (F014) is a straightforward spray-and-rinse process. Its triple-action formula is engineered to aggressively dissolve baked-on brake dust, grease, and road grime without damaging your wheel finish.

Step-by-Step Instructions

Work with Cool Wheels: Never spray the cleaner onto hot wheels right after driving. Let them cool down completely, and work on one wheel at a time to prevent the chemical from drying out on the rims.

Pre-Rinse: Spray the wheel thoroughly with a hose or pressure washer to blast away loose mud and surface grit.

Spray the Cleaner: Hold the bottle about 6 inches away and completely saturate the wheel faces, spokes, and inner rim barrels with the cleaner.

Let it Dwell: Allow the liquid to sit and pe*****te the stubborn grime for 30 seconds.

Agitate (For Heavy Grime): If your wheels have a thick layer of baked-on brake dust, gently scrub the surfaces using a soft detailing brush, wheel woolie, or a dedicated microfiber sponge.

Rinse and Dry: Blast the wheel thoroughly with a strong stream of water to wash away all chemical residue and dissolved dirt. Immediately dry the rim with a soft, clean microfiber towel to prevent mineral water spots from forming.



ā—Flamingo Car Care Philippines - Authorized DistributoršŸ¦© ā—Using Flamingo Tire Shine is quick and doesn't require any wip...
01/06/2026

ā—Flamingo Car Care Philippines - Authorized DistributoršŸ¦© ā—

Using Flamingo Tire Shine is quick and doesn't require any wiping if you use the standard spray version. Here is the short summary on how to apply it for the best results:

3-Step Application

Clean & Dry: Wash your tires thoroughly to remove any dirt, mud, or brake dust, and let them dry completely.

Shake & Spray: Shake the can well. Hold it 8 to 12 inches away from the tire and spray an even layer entirely around the side wall.

Let it Dry: Leave it alone to dry for at least 5 minutes. You do not need to wipe itā€”any small drips or runs will automatically disappear as it settles into a smooth, glossy finish.



ā—Flamingo Car Care Philippines - Authorized DistributoršŸ¦© ā—Step-by-Step InstructionsPre-Rinse Excess Mud: If your tires a...
30/05/2026

ā—Flamingo Car Care Philippines - Authorized DistributoršŸ¦© ā—

Step-by-Step Instructions
Pre-Rinse Excess Mud: If your tires are heavily caked in mud or thick debris, spray them down briefly with water first. If they only have light road dust, you can skip the washing step entirely.

Shake the Can: Shake the aerosol can vigorously for a few seconds to fully activate the foaming agents inside.

Spray Evenly: Hold the can roughly 6 to 8 inches away from the tire. Spray a steady, circular coat directly onto the sidewall, ensuring the foam completely covers the surface in a uniform white layer.

Walk Away: Do not wipe or scrub the foam. Simply leave the tire alone for 10 to 15 minutes. The thick foam will naturally collapse, dissolve the surface film, and dry into a glossy, dark-black protective shell.



ā—Flamingo Car Care Philippines - Authorized DistributoršŸ¦© ā—Using Flamingo Shine & Protects is an easy way to clean, polis...
29/05/2026

ā—Flamingo Car Care Philippines - Authorized DistributoršŸ¦© ā—

Using Flamingo Shine & Protects is an easy way to clean, polish, and shield vinyl, leather, plastic, and rubber surfaces from UV damage.

Step-by-Step Instructions
Prep the Surface: Wipe away any loose dust, mud, or debris with a damp cloth and let it dry completely.

Shake Well: Shake the bottle thoroughly before use to mix the active protective formula.

Apply the Product:

For broad sections: Spray directly onto the surface from about 6 inches away.

For tight areas (like dashboards near the windshield): Spray directly onto a clean microfiber cloth first to avoid overspray on glass or electronics.

Buff Dry: Spread the liquid evenly using a clean microfiber towel. Let it pe*****te for a minute, then flip the towel to a dry side and buff to a deep, clean shine.



Address

Banawe
Quezon City
1114

Opening Hours

Monday 8:30am - 5:30pm
Tuesday 8:30am - 5:30pm
Wednesday 8:30am - 5:30pm
Thursday 8:30am - 5:30pm
Friday 8:30am - 5:30pm
Saturday 8:30am - 5:30pm

Website

Alerts

Be the first to know and let us send you an email when Flamingo Car Care Philippines - Authorized Distributor posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share

Category