Rob's Detailing

Rob's Detailing Contact information, map and directions, contact form, opening hours, services, ratings, photos, videos and announcements from Rob's Detailing, Auto Detailing Service, Morwell.

06/02/2021

💦😏

Look at that reflection 😎. Carried out full exterior detail by cleaning the tyres and wheels first with Meguairs ultimat...
06/02/2021

Look at that reflection 😎. Carried out full exterior detail by cleaning the tyres and wheels first with Meguairs ultimate wheel cleaner followed by a 2 bucket method wash using Meguairs soft gel car wash. For the decontamination stage i used a iron remover spray and applied heavily on all surfaces of the vehicle, I allowed the chemical to dwell on the vehicle for a few minutes before pressure washing all iron particles that have been lifted off the surface from the chemical. I then go around the entire vehicle with the same iron decontamination spray wiping every panel and glass surface down ensure all road tar and any existing waxes or sealants have been removed. For the next stage I use a 6" clay disk that is attached to my 21mm orbit duel action polisher for lager areas and then I step down to a clay bar and clay block for the smaller areas i take my time to ensure all embedded contamination has been removed from the vehicle. Once the vehicle has been fully decontaminated i carry out a IPA (Isopropyl alcohol) wipe down on the vehicle to make sure there is no left over residue. Now its time for the paint correction. Lucky for me this Trailblazer have very little/minor scratches on the paint so I only carried out a single stage correction by using the Chemical Guys VSS all in one pollish. I then carried out another IPA wipe down on the vehicle to remove any oils that have been left behind from the pollish. For the final stage I decided to use Mothers CMX ceramic spray coating for the paint protection I applied a total of 3 coats to all paint and glass surfaces. Once that was done I applied Chemical Guys Silk Shine Dressing to all plastic trims and tyres. (20+ hours of work.)

Before and after shots of the interior of a Mazda 6. Started removing all loose rubbish and collecting all personal item...
08/03/2020

Before and after shots of the interior of a Mazda 6. Started removing all loose rubbish and collecting all personal items, followed by removing the front and rear seats. To vacume and extract all dirt from the carpets. While the seats are out of the car I used an APC (All purpose cleaner) to clean and agitate all the dirt embedded in the pores of the leather, then treated with a leather conditioner to rejuvenate and bring back the OEM look back to the leather. Followed by a thorough clean of the dash, center console, steering wheel area. Then all plastic trims and door trims have been cleaned and dressed with a UV protectant.

Carried out a full exterior detail. With the first step stating at the wheels with Meguirs heavy duty iron degeaser that...
08/03/2020

Carried out a full exterior detail. With the first step stating at the wheels with Meguirs heavy duty iron degeaser that reacts to metal/iron deposits. Second step is followed by a two bucket method wash useing Auto Glym foam cannon wash, and Chemical Guys bug and Tar remover. Then it was time for the paint decontamination possess, useing Bowden's Own three way iron decontamination spray and clubricant, sprayed thoroughly on the paint using a Car Pro 6 inch clay disk attached to my 21mm throw dual action pollishing mechine for the larger areas and meguirs clay bar for the smaller areas. Then it was time to wipe the car down with Car Pros IPA (Isopropyl alcohol spray) to remove any left over residue from the decontamination stage. Then the next step was to mask off any exterior trims for the pollishing stage, once done I decided to use the Chemical Guys hexlogic 6.5 inch Green light pollishing pad for the larger areas and a 4 inch Green hexlogic pad for the smaller areas, in combination with Chemical Guys V36 light polish liquid. This combination of pad and polish was perfect to remove the light scratches and swerls in the clear coat as well as removing any oxidation on the surface. After spending a thorough amount of time pollishing the surface it was time to wipe car down with Car Pros IPA spray again to remove all the residue from the polish. After this stage was done it was finaly time apply a ceramic coating useing Mothers CMX Hybrid ceramic coating spray.

Address

Morwell, VIC
3840

Website

Alerts

Be the first to know and let us send you an email when Rob's Detailing posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Shortcuts

Share

Category