Bill’s Saw Shop and Small Engines

Bill’s Saw Shop and Small Engines Chainsaw and small engine repair including ATV/SXS serving the Marshall, MN area and beyond.

It’s been a while, but we are still here!!! It’s been a busy summer working on all different types of projects and even ...
12/04/2023

It’s been a while, but we are still here!!! It’s been a busy summer working on all different types of projects and even though the weather is still nice, old man winter and snow is upon us. Come on down and get those snowblowers ready to go before waking to a driveway full of snow, just to find that your snowblower won’t start. We are offering 15% off labor charges for the month of December, so don’t wait bring in whatever you need fixed.

Did a call on a sawmill. This sawmill needed a tuneup, which included replacing rubber belting on the blade pullies. I a...
06/09/2023

Did a call on a sawmill. This sawmill needed a tuneup, which included replacing rubber belting on the blade pullies. I also changed the engine oil and greased the mill. Bring your small engines to Lynd!

We’re still lawnmower crazy here. Bring your small engines to Lynd!
05/17/2023

We’re still lawnmower crazy here. Bring your small engines to Lynd!

Brought a lawnmower back to a customer. Bring your small engines to Lynd!
05/04/2023

Brought a lawnmower back to a customer. Bring your small engines to Lynd!

This is a Husqvarna 23 compact that came in not running. I found that the saw had bad gas in it. I replaced the fuel lin...
04/21/2023

This is a Husqvarna 23 compact that came in not running. I found that the saw had bad gas in it. I replaced the fuel line and fuel filter, removed the carburetor, cleaned, and installed a kit. I put the saw back together, fueled, and adjusted the carburetor. It now works great!

04/04/2023

Spring’s almost here. Get 10% off labor charges now through the end of the month!

This is a Honda generator that came in with running issues. I removed the bad gas and carburetor to clean it. I then cha...
03/28/2023

This is a Honda generator that came in with running issues. I removed the bad gas and carburetor to clean it. I then changed the spark plug and removed the valve cover to check the valves. The valve tolerances were good. I then removed the back covers to access the muffler. I removed the spark arrestor to clean it. I put the generator back together, fueled, and started it. The generator still didn’t run good. I removed the front control panel to look at the circuit board and relays. I found a bad wire on the circuit board and repaired it. I put it back together and started it again. The generator now runs good. Bring your small engines to Lynd!

Wet snow in the spring can get pretty heavy. Can your snowblower handle it? If you have one that needs to get looked at,...
03/21/2023

Wet snow in the spring can get pretty heavy. Can your snowblower handle it? If you have one that needs to get looked at, bring it to Bill’s Saw Shop and Small Engines.

This is a snowblower that came in today. The customer was surprised we were still open! Apparently, there is a rumor goi...
03/14/2023

This is a snowblower that came in today. The customer was surprised we were still open! Apparently, there is a rumor going around that we closed the shop. It’s definitely NOT true, so spread the word. We fix saws, snowblowers, lawnmowers, side by sides, w**d eaters, 4 wheelers, and much more!

Bringing a few items I fixed back to a customer. If you have a small engine that needs fixing, bring it to Lynd.
03/04/2023

Bringing a few items I fixed back to a customer. If you have a small engine that needs fixing, bring it to Lynd.

Eighteen inches is a lot of snow to move with a snowblower that isn’t running right. If your blower let you down during ...
02/25/2023

Eighteen inches is a lot of snow to move with a snowblower that isn’t running right. If your blower let you down during this last storm, bring it down and we’ll get it running again.

Put it a twelve volt battery cutoff switch. Then I picked up a snowblower, generator, and chainsaw to fix. Bring your sm...
02/09/2023

Put it a twelve volt battery cutoff switch. Then I picked up a snowblower, generator, and chainsaw to fix. Bring your small engines to Lynd!

Address

112 N Redwood Street
Lynd, MN
56157

Opening Hours

Monday 8am - 8:30pm
Tuesday 8am - 8:30pm
Wednesday 8am - 8:30pm
Thursday 8am - 8:30pm
Friday 8am - 8:30pm
Saturday 8am - 8:30pm
Sunday 11am - 4pm

Telephone

+15074017592

Website

Alerts

Be the first to know and let us send you an email when Bill’s Saw Shop and Small Engines posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Bill’s Saw Shop and Small Engines:

Shortcuts

Share