Stone Guru

28/10/2026

While the machine makes thousands of rotations, we move forward by a few centimetres.

It looks a lot like a dance. The machine brings the spin, the operator sets the pace, and when the two know each other well, neither rushes and neither steps on the other’s toes. Pass after pass, the floor comes up even, section by section.

That’s where the finish comes from, and the satisfaction too.

26/10/2026

Meet the newest member of the Stone Guru fleet. It’s built for the big jobs.

The Hyper Grinder HGE 2500 RX has multiple grinding heads, 25-horsepower motors, and a lot more floor covered with every pass.

It even changes the question we ask about a new job. It used to be “can it be done?” Now it’s “when do we start?”

23/10/2026

The bigger the floor, the sharper the focus has to be. A reception area like this means hours of steady, even passes, and a single lapse in attention shows up in the finish.

You’d think that kind of concentration would wear thin by the afternoon. It doesn’t, because we can see the stone coming through under the slurry, and we know exactly how the floor will look once it’s rinsed.

With results like these, staying focused is the easy part.

21/10/2026

Some jobs call for one machine. This one called for all of them.

It’s one of the largest projects we’ve taken on: the full team on site and every machine we work with lined up on the floor, from heavy grinders to polishers.

At the end, the floor reflects the whole line-up back at us. Clean, even, impeccable.

19/10/2026

We get asked how we find the patience to go over the same floor again and again, pass after pass.

The answer is simpler than it sounds. We’re not thinking about the twentieth pass. We’re thinking about what the floor will look like at the end of them, because we’ve seen that result before and we know it’s there to be found.

This patterned floor at the foot of the staircase is a good example: water, slurry, slow even passes around the ironwork, one section at a time.

The repetition is the job. The result is the reason.

16/10/2026

One word keeps coming back to us whenever we hand over a finished job: 𝑺𝑨𝑻𝑰𝑺𝑭𝑨𝑪𝑻𝑰𝑶𝑵.

This floor says it better than we can. A deep, even polish that picks up the light and holds it, from tile to tile, with the veining of the stone clear and clean again.

It's the result of patient, careful work, pass after pass, until nothing is left to correct.
And then the moment we wait for: the client sees the finished floor and is more than happy with it.

14/10/2026

Not every restoration happens on site. Some of the best work happens on a workshop table, one slab at a time.

The diamond pads are lined up in order, the machine moves in slow, even circles, and you can see the surface changing under it: the dull, cloudy patches give way to a clean, uniform finish. A slab can’t be rushed or bluffed. Every pass either does the job or leaves a mark.

Smaller surface, same standard.

12/10/2026

Patience matters. Skill matters. But neither gets very far without the right machine under your hands.

The Titan 530 is doing the heavy lifting here, moving across two different marbles, cream and deep red, and taking each one back to a clean, even surface without fuss. It handles the tough, uneven work so the person guiding it can focus on the detail.

Good hands need good equipment. We make sure to have both.

08/10/2026

From the outside, grinding a floor looks like walking up and down a room behind a machine. From the inside, it’s anything but dull.

Today’s room is wrapped in plastic, the artwork protected, a pale slurry spreading with every pass. Under it, the stone is slowly coming back from layers of dirt and wear, one section at a time. Nobody knows exactly what’s down there until the machine gets to it, and that is half the fun.

The other half is the client walking in afterwards, looking at a floor they’d stopped noticing, and seeing it properly again.

As long as there’s a treasure under the grime, this job will never be boring.

05/10/2026

Has your marble lost its finish?

Scratches, dull patches, stains, acid marks or worn areas don’t always mean the stone needs replacing — and they don’t always require a full restoration either.

At Stone Guru, we assess the surface first and recommend only the treatment it actually needs, whether that means specialist cleaning, polishing, a local repair or complete restoration.
We work with marble, limestone, travertine, terrazzo, granite and other stone surfaces in private homes and commercial properties across London.

20+ years of hands-on stone restoration experience.
If you’re not sure what your stone needs, send us a few details and photos.

We’ll take a look and tell you the sensible next step.
Get your free stone assessment:

Get your quote on Stone floor restoration in London: marble, granite, terrazzo, travertine, limestone and concrete. We don cleaning, polishing and repairs.